Powermax + Easy Install and Setup
|
|
Introduction
This install guide we will cover how to
set up a basic system with a remote keyfob, 1 door contact and 1 PIR.
Adjust entry/exit delays, bell times, etc. Diagnostic testing, triggering the system and sending
telephone reports.
|
| |
Access the user menu
Press 'next' until 'USER SETTING' is displayed
Press 'ok' and enter the user code (1111 by default)
Pressing 'next' scrolls through the options in the user menu
To exit press 'Away' , the display will show '<OK> TO EXIT' , press 'ok'
|
| |
‘User permit' function
The default for this is enabled. In this state, the user will have
to allow the installer access to the installer menu. This is done by
first accessing the 'user setting' menu, then selecting 'installer
mode' With this disabled 'installer mode' becomes the next option
after 'user setting' in the main menu.
Access the installer menu
|
| |
Access the user menu
Press next until 'INSTALLER MODE' is displayed (if you go past it,
press 'back' to back up)
Press 'ok' and enter the installer code (9999 by default)
Pressing 'next' scrolls through the options in installer mode
To exit press 'away' , the display will show '<OK> TO EXIT' , press
'ok'
|
| |
Change the user code
- Important -The user and installer codes must be different
- Access user menu
- Press 'next' until 'SET USER CODES' is displayed
- Press 'ok'
- Display will show 'USER CODE l' , press 'ok'
- Enter new user code and press 'ok'
- Press 'away' and 'ok' to exit
|
| |
Change the installer code
- Access the installer menu
- Display will show 'NEW INSTL CODE' , press 'ok'
- Enter new code and press 'ok'
- Press 'away' and 'ok' to exit.
|
| |
Enrol a keyfob
| This procedure covers only the 'code secure' MCT234. Other button
transmitters are enrolled as 'WL devices'. |
 |
- Access installer mode
- Press 'next' until 'ENROLLING' is displayed
- Press 'ok'
- Press 'next' until 'ENROLL KEYFOB' is displayed
- Press 'ok'
- Enter keyfob number 1 or press next until 1 is displayed
- Press 'ok'
- Display shows 'TRANSMIT NOW'. Press one of the keyfob buttons
- Panel will beep and the display will show 'keyfob l' with a
shaded square on the right.
- Press 'away' and 'ok' to exit.
- Test the keyfob by arming and disarming the system using the
'locked padlock' and 'unlocked padlock' buttons.
|
|
| |
Enrolling wireless devices WL device Before enrolling
devices, you need to decide where they will be installed and which
type of area they will protect (i.e. interior, perimeter, delay,
etc. and the room name).
Note zone 1 default is 'front door' and type is 'delay 1', this
means when the door is opened a delay will elapse before the alarm
sounds.
We will use the default zone 1
setting, however zone 2 will need to be set to 'interior' and
'hall'. see Defining Zones.
|
Zone No. |
Zone Type |
Zone Name |
Chime
(melody / Zone name / Off) |
|
Default |
Programmed |
Default |
Programmed |
| 1 |
Delay 1 |
|
Front Door |
|
|
| 2 |
Delay 1 |
|
Garage |
|
|
| 3 |
Delay2 |
|
Garage Door |
|
|
| 4 |
Perimeter |
|
Back Door |
|
|
| 5 |
Perimeter |
|
Child Room |
|
|
| 6 |
Interior |
|
Office |
|
|
| 7 |
Interior |
|
Dinning Room |
|
|
| 8 |
Perimeter |
|
Dinning Room |
|
|
| 9 |
Perimeter |
|
Kitchen |
|
|
| 10 |
Perimeter |
|
Living Room |
|
|
| 11 |
Interior |
|
Living Room |
|
|
| 12 |
Interior |
|
Bedroom |
|
|
| 13 |
Perimeter |
|
Bedroom |
|
|
| 14 |
Perimeter |
|
Guest Room |
|
|
| 15 |
Interior |
|
Master Bedroom |
|
|
| 16 |
Perimeter |
|
Master Bedroom |
|
|
| 17 |
Perimeter |
|
Laundry Room |
|
|
| 18 |
Perimeter |
|
Master Bathroom |
|
|
| 19 |
Perimeter |
|
Basement |
|
|
| 20 |
Fire |
|
Fire |
|
|
| 21 |
Fire |
|
Fire |
|
|
| 22 |
Emergency |
|
Emergency |
|
|
| 23 |
Emergency |
|
Emergency |
|
|
| 24 |
24 h / silent |
|
Basement |
|
|
| 25 |
24 h / silent |
|
Office |
|
|
| 26 |
24 h / audible |
|
Attic |
|
|
| 27 |
24 h /audible |
|
Den |
|
|
| 28 |
non-alarm |
|
Yard |
|
|
| 29 |
non-alarm |
|
Hall |
|
|
| 30 |
non-alarm |
|
Utility Room |
|
|
|
| |
Enrolling types
|
|
Normal Enrol |
When making a transmission from the device, this should
be an alarm signal. i.e. remove the magnet on a magnetic
contact, or move in front of a PIR. Also on a PIR, inserting the
battery will make the unit transmit |
|
Enrol by Tamper |
To make a transmission in this mode, press the tamper
switch on the device. |
|
| |
Enrol magnetic contact using 'normal enrol'
- Access installer mode
- Press 'next' until 'ENROLLING' is displayed
- Press 'ok'
- Press 'next' until 'ENROLL WL DEVICE' is displayed
- Press 'ok' until 'ZONE No --' is displayed
- Enter zone number 01, or press 'next' until 01 is displayed.
(note, if a device is present there will be a shaded square next to
the zone number. Another device cannot be enrolled to this zone)
- Press 'ok' , display will show 'TRANSMIT NOW'
- Make a transmission from the magnetic contact -refer to
'enrolling types' above
- Panel will beep and the display will show 'zone 01' with a shaded
square to the right.
- Press 'away' and 'ok' to exit
- Test by removing and replacing the magnet. Display will show
'FRONT DOOR OPEN/CLOSED'
|
| |
Enrol PIR using 'enrol by tamper'
- Access installer mode
- Press 'next' until 'ENROLLING' is displayed
- Press 'ok'
- Display will show 'ENROLLING TYPE', press 'ok'
- Press 'next' until 'by tamper' is displayed
- Press 'ok' twice
- Press 'next' until 'ENROLL WL DEVICE' is displayed
- Press 'ok' until 'ZONE No --' is displayed
- Enter zone number 02, or press 'next' until 02 is displayed.
(note, if a device is present there will be a shaded square next to
the zone number. Another device cannot be enrolled to this zone)
- Press 'ok' ,display will show 'TRANSMIT NOW'
- Make a transmission from the PIR by pressing the tamper spring
- Panel will beep and the display will show 'ZONE 02' with a
shaded square to the right. This can be confirmed by pressing the
spring again -the panel will beep again.
- Press 'away' and 'ok' to exit.
|
| |
- Access installer mode
- Press 'next' until 'DEFINE ZONES' is displayed. Press 'ok'
- Enter '02' or press next until display shows 'ZONE 02'
- Press 'ok' , display will show Z02 TYPE'
- Press 'ok'
- Press 'next' until 'interior' is displayed. Press 'ok' twice
- Display will show 'Z01 NAME' , press 'ok'
- Press 'next' until- 'Hall' is displayed. Press 'ok' twice
- Display will show 'Z02 CHIME' we are not changing chime from
default (off)
- Press 'away" and 'ok' to exit.
|
| |
Setting an 'entry delay'
- Access 'installer mode'
- Press 'next' until 'DEFINE PANEL' is displayed. Press 'ok'
- Display will show '01:ENTRY DELAY l' , press 'ok'
- Press 'ok' until 'entry delay1 15s' is shown.
- Press 'ok' twice
- continue to next section
|
| |
Setting an 'exit delay'
- Press 'next' until '03:EXIT DELAY' is displayed. Press 'ok'
- Press 'next' until 'exit delay 30s' is displayed (pressing 'back'
instead scrolls backwards -this is quicker).
- Press 'ok' twice
- continue to next section
|
| |
Setting 'bell time'
- Press 'next' until '04:BELL TIME' is displayed. Press 'ok'
- Press 'next' or 'back' until 'bell time 1m' is displayed
- Press 'ok' twice
- continue to next section
|
| |
- Press 'next' until '05:ABORT TIME' is displayed
- Press 'ok'
- Press 'next' or 'back' until 'abort time 00s' is displayed
- Press 'ok' twice
- Press 'away' and 'ok' to exit
|
| |
Testing the System
|
Diagnostic testing.
- Position the PIR either out of sight, or inside it's box for 2
minutes.
- Access 'installer mode'
- Press 'next' until 'DIAGNOSTICS' is displayed
- Press 'ok'
- 'WL SENSORS TEST' is displayed. Press 'ok'
- 'DIAG TESTING' is displayed. Trigger both sensors by opening the
magnetic contact and moving in front of the PIR
- Each time a signal is received the panel will beep and display
the zone name.
- Press 'ok' to scroll through the results 9. Press 'away' and 'ok'
to exit.
|
| |
Triggering detectors
- Position the PIR either out of sight, or inside it's box
- Arm the system 'away' -either by pressing 'away' and entering the
user code, or by pressing the 'locked padlock' button on the keyfob.
- Wait for the exit beeps to stop
- Simulate the front door being opened by removing the magnet.
- The panel will start beeping and ask you to disarm
- Disarm by either pressing 'off and entering the user code, or by
pressing the 'unlocked padlock' button on the keyfob.
- Repeat this and experiment by triggering the PIR first or after
opening the door, (the alarm will sound).
|
| |
- Access 'installer mode'
- Press 'next' until display shows 'DEFINE COMM'
- Press 'ok'
- Press 'next' until display shows' 17: SET PRVT TEL'
- Press 'ok'
- Display shows '1st private tel#' , press 'ok'
- If you have a mobile number, enter this or another
landline number you wish to report too
- Press 'ok' twice
- Press 'home' ,display will show' 17: SET PRVT TEL'
- Press 'next' until display shows '20 REPORT>PRVT', press 'ok'
- Select option 'all (-op/cl)' ('next' to scroll and 'ok' twice to
select)
- Press 'away' and 'ok' to exit
- Experiment by triggering the system (setting the alarm off,
or tampering with a detector) the phone will ring and a voice
message will be heard. Pressing '2' on the-phone acknowledges
the call and the powermax will hang up.
|
| |
Troubleshooting
|
| |
User / Installer codes not working
- If you have changed the codes, make sure you are using the new
one and not the default.
- Make sure the user and installer codes are not the same -if so,
changing one of them will allow access.
|
| |
Devices don't trigger the panel
Make sure the correct device has been enrolled. See 'deleting
a device' and enrol it again.
|
|
|
PIR doesn't detect movement
Wireless PIR's have a sleep timer. After detection, the device will
need 2 minutes with no movement before it will activate again.
|
| |
Alarm sounds, but private telephone doesn't ring
- Check connection between the Powermax and telephone socket
- Make sure' ABORT TIME' is set to '00' see 'setting
abort time'
- Repeat procedure 'reporting to private telephones'
Make sure the number is entered correctly and 'REPORT>PRVT' is not
disabled
|
| |
'Trouble' light is illuminated
Press 'SHOW/OK' button repeatedly, each time listening to the voice
prompts. The reason will be announced.
|
| |
Display shows 'NOT READY' and trouble light illuminated
Most likely cause is a door has been left open or a detector casing
is not fitted. Pressing 'SHOW/OK' repeatedly and listen for '******
OPEN' , this will be the cause.
|
|
|
- Access installer mode
- Press 'next' until 'ENROLLING' is displayed. Press 'ok'
- Press 'next' to select the type of device to delete (WL device, keyfob, 1 way keypad, siren)
- Press 'ok'
- For 'WL' devices, press 'ok' until 'ZONE No' is displayed
- Enter the zone/device number, or press 'next' until the number is
displayed (note, if a device is present the number will have a
shaded square next to it)
- Press 'ok'
- Display will show '<off> to delete'
- Press 'off'
- At this point, pressing 'ok' will allow you to transmit a new
device for this zone
- Repeat steps 7 -10 for other devices of the same type.
- Press 'away' and 'ok' to exit.
|
 |
Login Status
